Author Topic: Increasing the reverb on drum track  (Read 4037 times)

0 Members and 1 Guest are viewing this topic.

Offline karl28

Increasing the reverb on drum track
« on: April 26, 2021, 05:07:39 PM »
Hi,
I've created a midi file on computer of a drum track for a song. I've loaded this into my Genos and I want to increase the reverb on the drum track which is track 10. I've gone into mixer & increased the reverb but it's not increasing it.
I gather I must be doing something wrong. I've done it before but can't remember the process. Can anyone help?

Thanks,

Karl
 

Offline EileenL

Re: Increasing the reverb on drum track
« Reply #1 on: April 29, 2021, 11:29:49 AM »
You have to go to step edit and select track ten and alter the reverb on this track.

Offline DerekA

Re: Increasing the reverb on drum track
« Reply #2 on: April 29, 2021, 12:37:52 PM »
I've created a midi file on computer of a drum track for a song. I've loaded this into my Genos and I want to increase the reverb on the drum track which is track 10. I've gone into mixer & increased the reverb but it's not increasing it.

This should work. First obvious question would be, is there actually a reverb program assigned and is it switched on.
Genos
 

Offline karl28

Re: Increasing the reverb on drum track
« Reply #3 on: April 29, 2021, 01:22:20 PM »
Thanks Eileen for your reply. I'll do that :-)
 

Offline EileenL

Re: Increasing the reverb on drum track
« Reply #4 on: April 29, 2021, 03:44:45 PM »
If you can't find reverb on this control track you can insert one and then adjust it to suit.

Offline karl28

Re: Increasing the reverb on drum track
« Reply #5 on: April 29, 2021, 06:29:23 PM »
I can’t it that way. When I spoke to Yamaha tech support a few months ago, I’m sure I had to go into mixing console but when I’ve done that it’s not altering it.
 

Offline overover

Re: Increasing the reverb on drum track
« Reply #6 on: April 29, 2021, 09:28:11 PM »
Hi Karl,

did you create this MIDI file on the computer "from scratch", or did you just edit a MIDI file that was recorded on the Genos before (or a commercial MIDI file) on the computer?

If the former is the case: Has it been ensured that the MIDI file contains the necessary resets (GM and XG reset) as well as the setting of a certain Reverb Type and an event to set the Reverb Send Level (CC 91)?

If you want to use an Insert Effect block for the Drum reverb, the corresponding SysEx should be in the MIDI file. (In this case the send level for the system REVERB effect block should be set to zero via CC 91).

By the way: The system CHORUS send level should be set to zero for drum channels or, if necessary, only turned up very slightly (via CC 93).


My recommendation is alwas to begin with a MIDI (Quick) recording directly on the keyboard. Then import this MIDI file into the DAW on the computer. This way you will automatically have many of the required MIDI controllers and SysEx events in the MIDI file.


Best regards,
Chris
« Last Edit: April 29, 2021, 09:30:33 PM by overover »
➪ Everyone kept saying "That won't work!" - Then someone came along who didn't know that and just did it.
➪ Never put the manual too far away: There's more in it than you think! ;-)
 

Offline karl28

Re: Increasing the reverb on drum track
« Reply #7 on: April 29, 2021, 10:19:47 PM »
Hi Chris,
I wrote the drum part out in Sibelius, then exported it as a midi file, then loaded it into my Genos.
As it happens, it hadn’t played the hihats which I suspect was because of the drum mapping so I ended up doing the drum part in style creator.
I normally work with a drummer so I’ve hardly used the style creator but due to lockdown, I’ve got extra time on my hands which allows me time to explore some of the other features which don’t normally get used.
Many thanks for your response and tips.

Best wishes,

Karl