Author Topic: Make your own Genos screenprotector  (Read 796 times)

0 Members and 1 Guest are viewing this topic.

Make your own Genos screenprotector
« on: March 20, 2018, 08:35:38 PM »
Because I didn't like the fingerprints every time I've played the Genos, I found a simple and easy solution to make your own screen protector. I'm also worried that the fingerprints will damage the touch sensitive screenlayer by leaving nasty spots.

As most Genos users have notices, there is a thin plastic layer on the screen that responds to pressure. So using a screenprotector with a little sticky layer seems to be a bad idea, leaving nasty airbubbles and having troubles removing the screenprotector.

So I made my own screenprotector by using a simple, cheap A4 pocket sleeve (used to put A4 paper in ordners). Advantages:
- cheap
- soft plastic
- passing light and clear screen picture
- it has a light stucture causing an anti-clare layer which doesn't show much fingerprints
- doesn't stick, so no airbubbles
- easy to remove and/or to replace

After secure cutting a piece of 202mm x 118mm, it is ready to be put on the Genos screen. Just make sure to clean the Genos screen (for the last time ;D). There is a little margin under the hard plastic edge of the screen, so the created screen protector doesn't leave open gaps.







« Last Edit: March 21, 2018, 12:07:35 AM by robbiedoes »
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Everything about my musical activities and Tyros 5: http://www.robbiedoes.nl/index_uk.htm
 
The following users thanked this post: jerryghr, Lee Batchelor, dtah80, maartenb

Offline Rien5

Re: Make your own Genos screenprotector
« Reply #1 on: March 20, 2018, 08:54:49 PM »
Robbie,
Thank you for the excellent proposal.
I did the same this evening and it meets my expectations !
Regards,
Rien
 

Re: Make your own Genos screenprotector
« Reply #2 on: March 20, 2018, 10:22:02 PM »
Hello Rien,

Nice to read that it helped you :).
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Everything about my musical activities and Tyros 5: http://www.robbiedoes.nl/index_uk.htm
 

Offline Al Ram

Re: Make your own Genos screenprotector
« Reply #3 on: March 20, 2018, 10:28:54 PM »
Great idea !!

I will try it . . . .

For those not familiar with the metric system and millimeters,

the measurements provided by Robbie translate to 8 inches by 4 inches 5/8.   plus or minus one millimeter or 1/16 of an inch.

I already cut a paper template and will try with the inlay sheet tomorrow.   


thanks  a lot
« Last Edit: March 20, 2018, 11:49:53 PM by Al Ram »
AL
San Diego/Tijuana
 

Offline Lee Batchelor

Re: Make your own Genos screenprotector
« Reply #4 on: March 20, 2018, 10:33:00 PM »
Robbie, you're not as dumb as I look (LOL)!! Thanks for the tip. I shall give it a whirl. I have a bunch of those exact sleeves. Never thought of re-purposing them like that. Best...

- Lee :)
Current Gear: Genos, SoundCraft mixer, two Bose L1 Compacts, 15 inch sub designed and built by myself, Yamaha HS8 studio monitors, Cubase 8 Artist, Steinberg UR-44.
 

Offline Lee Batchelor

Re: Make your own Genos screenprotector
« Reply #5 on: March 22, 2018, 12:13:16 PM »
Works great, Robbie. Thanks!
Current Gear: Genos, SoundCraft mixer, two Bose L1 Compacts, 15 inch sub designed and built by myself, Yamaha HS8 studio monitors, Cubase 8 Artist, Steinberg UR-44.
 

Offline Stijn

Re: Make your own Genos screenprotector
« Reply #6 on: March 22, 2018, 08:21:15 PM »
Thank you Robbie,

Good idea!
I took your advice a step further. Instead of an A4 pocket sleeve I used a transparency sheet for ink jet printers.
This transparency sheet is really clear and is much firmer then a pocket sleeve which makes it easier to handle and to cut.
No ripples either. And also, the sheet stays free of fingerprints.

It is hardly visible on the display and the touch screen works just fine.

Stijn
One good thing about music; when it hits you, you feel no pain.
 

Offline Helmer dk.

Re: Make your own Genos screenprotector
« Reply #7 on: April 11, 2018, 06:43:08 PM »
Hi Robbie and Stijn

Thank you for the good idea and further development of the good idea, I have taken the idea myself and I do not miss my fingerprints!  ;)

Regards Helmer
 

Offline Al Ram

Re: Make your own Genos screenprotector
« Reply #8 on: April 11, 2018, 07:31:32 PM »
Thank you Robbie,

Good idea!
I took your advice a step further. Instead of an A4 pocket sleeve I used a transparency sheet for ink jet printers.
This transparency sheet is really clear and is much firmer then a pocket sleeve which makes it easier to handle and to cut.
No ripples either. And also, the sheet stays free of fingerprints.

It is hardly visible on the display and the touch screen works just fine.

Stijn

I did the same . . . . .
AL
San Diego/Tijuana